Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Wood & steel frame
Before
After
Before
After
Before
AfterWhy Laguna Beach Homeowners Choose Ghost Controls Gate Repair
Ironworks Gate Co. provides independent Ghost Controls service in Laguna Beach, from the flat PCH-adjacent cottage streets to the steep canyon drives in Temple Hills and Top of the World. We work on Ghost Controls swing and slide operators every month, and most repairs are completed in a single visit with the price settled before we turn a bolt. We are not affiliated with Ghost Controls and we are not an authorized dealer, but we are trained and equipped on their full residential line, and we stock the parts that fail most often here in the salt air. Call (442) 246-9347 any hour for a live person and a straight answer.
Why Trust Ironworks Gate Co. for Your Ghost Controls Gate Repair?
Owner Victor Salinas grew up near the Laguna Canyon Road corridor, studied metalwork and electrical systems at Saddleback College in Mission Viejo, and has spent the decades since working on gates in actual driveways, for actual neighbors. Around Laguna Beach, he is the guy people call when a Ghost Controls swing gate goes sideways after a salt-air winter or a slide motor quits on a Friday afternoon. Victor insists on one thing above all: we fix it right the first time, or we come back, simple as that. That is why every Ghost Controls repair we complete carries our written 90-Day Done Right Promise.
Our technicians see Ghost Controls systems in the field week after week. We know the TDS2 dual swing’s limit switch bracket, the AXD heavy-duty board’s surge sensitivity, and the R20 slide operator’s gearbox wear patterns. We carry genuine Ghost Controls components whenever they are available, and only well-tested aftermarket equivalents for discontinued boards or mechanical parts. Every technician who walks onto a Laguna Beach property is background-checked, uniformed, and guided by the K.E.Y.S. code: Krafted right, Every time, Your home first, Standing behind it.
Common Ghost Controls Gate Repair Problems We Fix in Laguna Beach
- Limit switch misalignment on TDS2 and AXD swing operators. A gate that stops short or over-travels usually traces back to a limit switch that has drifted or a bracket that has cracked, often after a hard wind event on an exposed hillside lot or an accidental impact. We recalibrate the limits on the control board and replace the bracket with a reinforced equivalent when needed.
- Control board failure from salt corrosion and power surges. Direct Pacific Ocean exposure sends salt-laden moisture into motor housings and board enclosures year-round. The near-permanent marine layer keeps metal surfaces damp even between storms, and we regularly see error codes that require board-level testing rather than a simple reset.
- Battery drain from a faulty solar charge controller or parasitic draw. Many off-grid Laguna Beach estates run Ghost Controls operators on solar with battery backup. When the battery drains within hours despite good sun, the cause is usually a charge controller that has failed or a parasitic draw on the board. We test the full charging circuit, not just the battery.
- Gearbox or drive arm wear causing grinding and slow operation. Heavy ornamental iron gates on hillside properties put real stress on Ghost Controls drive arms and gearboxes. Grinding noise and sluggish movement typically mean internal gear wear or a drive arm that is binding. We open the unit, inspect the wear pattern, and give you an honest repair-or-replace recommendation.
- Phantom reversal on TDS2 dual swing gates. A gate that starts to close then immediately reverses is often traced to a cracked limit switch bracket combined with a worn receiver module, not an obstruction. Our most recent Laguna Beach call for this symptom was a TDS2 on a hillside home in the canyon neighborhoods. We replaced the bracket with a reinforced equivalent and recalibrated the limits on the AXD board, and the gate has operated smoothly since.
Ghost Controls Parts & Our Repair-vs-Replace Approach
When a Ghost Controls Gate operator fails, the first question is usually parts. We use genuine Ghost Controls components whenever they are available, and only well-tested aftermarket equivalents for discontinued boards or mechanical parts. That matters because Ghost Controls has changed several board revisions over the years, and an older TDS2 that is no longer in production may need a carefully matched aftermarket board rather than a generic swap.
We stock the most common Ghost Controls parts locally for fast turnaround: limit switch brackets, receiver modules, solar charge controllers, and drive arms. When the gearbox is heavily worn or a control board shows multiple failed relays, we will tell you replacement is the better financial call rather than patching a unit that will fail again in six months. You get a square deal: upfront price, no surprises on the bill. Call (442) 246-9347 for an exact quote on your Ghost Controls repair.
Our Ghost Controls Service Process - Step by Step
- 1
Diagnosis on site. We test the Ghost Controls board, limit switches, receiver, and mechanical drive before touching anything else. On hillside Laguna Beach properties, we also check post plumb and footing integrity first, because downslope soil creep can throw a gate out of alignment and burn out a perfectly good motor.
- 2
Upfront written price. You approve the repair cost before we start. No open-ended labor, no surprises. Most Ghost Controls repairs are completed in the same visit.
- 3
Repair or replacement with correct parts. We use genuine Ghost Controls components where available, or tested aftermarket equivalents for discontinued items. Every part is matched to your specific model and board revision.
- 4
Calibration and load testing. We recalibrate open and close limits, test obstruction reversal, verify solar charging if applicable, and run the gate through a full cycle under load, not just in the shop.
- 5
Written 90-Day Done Right Promise. Every Ghost Controls job we complete is backed in writing. If it is not right, we come back and make it right. No paperwork, no arguing.
Ghost Controls Products We Service & Install in Laguna Beach
We service the full Ghost Controls residential line, including the TDS2 Series dual swing gate opener, the AXD Series heavy-duty swing gate opener, the R20 Series residential slide gate opener, and the XP2 Series single swing gate opener. We also install all four series for Laguna Beach homeowners who are upgrading from an older operator or adding automation to an existing manual gate, and we offer the same Ghost Controls in Laguna Niguel. Local stock includes common swing and slide motor parts, limit brackets, receivers, and solar charge controllers. If you are not sure which Ghost Controls model you have, call (442) 246-9347 and a live person will help you identify it while you stand at the gate.
We Also Service These Brands
Ironworks Gate Co. is not a single-brand shop. We are trained and equipped on nine gate-automation brands, including LiftMaster, Mighty Mule, DoorKing, FAAC, BFT, Linear, Viking, and Elite. If you own a different brand today and are considering Ghost Controls for a future upgrade, we can service what you have and advise on what fits your gate and your hillside, including Ghost Controls service in Aliso Viejo.
FAQs - Ghost Controls Gate Repair Service in Laguna Beach
No. We are an independent Ghost Controls service provider, not an authorized dealer or warranty station. That independence means our recommendations are based on what is actually wrong with your gate, not on moving a particular product line. We use genuine Ghost Controls parts whenever they are available and only tested aftermarket equivalents when a board or part has been discontinued.
Yes, whenever they are available. For discontinued Ghost Controls boards or mechanical parts, we source only well-tested aftermarket equivalents that we have installed and stood behind on other Laguna Beach gates. We never install a cheap generic board just to get the job done faster.
Most Ghost Controls repairs in Laguna Beach are completed in a single visit, usually within one to three hours on site depending on the failure. Board-level diagnosis, limit recalibration, and drive arm replacement are all same-visit jobs in most cases. We quote the repair before we start, and if a part must be ordered, we tell you exactly when it arrives and when we will be back.
We service and install the TDS2 dual swing series, AXD heavy-duty swing series, R20 residential slide series, and XP2 single swing series. If your unit is older than these model lines, call (442) 246-9347 and we will identify what you have from the plate on the operator housing.
If your Ghost Controls operator is still under the manufacturer’s warranty period, any independent service could affect warranty coverage, and we will tell you that plainly before we begin. For gates outside the warranty window, which is most of what we see on Laguna Beach properties with 25-to-30-year-old gates, our own written 90-Day Done Right Promise protects the work we do.
The most common Ghost Controls repairs in Laguna Beach, including limit switch calibration, bracket replacement, and receiver module replacement, typically run between $180 and $480 depending on the model and the part. Board replacement on a TDS2 or AXD typically runs higher, and we will give you a written price before any work begins. Call (442) 246-9347 for an exact quote on your Gate Repair, estimates are free.
Book Your Ghost Controls Service in Laguna Beach, CA
Call (442) 246-9347 any hour, any day. A live person answers, not a voicemail tree. Tell us what your Ghost Controls gate is doing, or not doing, and we will schedule a visit that fits your day. Free estimates, upfront pricing, and the written 90-Day Done Right Promise on every job we complete.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Laguna Beach since 1984.